DISCOFILM Record Cleaner – 500 ml Set with Sponge Dispenser & LP Bases
Record Cleaner | Vinyl Cleaner | CD/DVD/Blu-ray & DSLR Sensor Cleaning
✅ The original – proven for over 30 years
✅ For records, CDs, DVDs, Blu-rays & SLR camera sensors
✅ Made in Germany – hand-filled with love
Product description:
DISCOFILM is the classic among media cleaners – a honey-like liquid that reliably removes dust, dirt, grease, and even stubborn residues such as cola, beer, or ash. No mechanical action required – simply apply, let dry, wipe off – done!
Application:
- Pierce the center of the bottle.
- Coat the first side generously.
- Allow to dry for 30 minutes.
- Turn over and apply to the second side.
- Allow to dry for 2-4 hours (depending on room temperature).
- Apply adhesive tape, peel off – clean!
Tested & recommended:
The trade magazine Audio praised DISCOFILM after a rigorous test: “Like newly pressed” – a masterpiece for Berlin inventor Maximilian Müller.
Conclusion:
Whether after a party or in everyday life – DISCOFILM makes your records shine again. Simple, effective, and gentle.
Scope of delivery:
- 1x bottle of DISCOFILM (500 ml)
- 2x LP bases (underlays for cleaning)
- 1x dispenser (for applying DISCOFILM)
DISCOFILM Vinyl Cleaning Kit – Complete kit for record and LP care
How to use DISCOFILM SET – step by step
1. Preparation
Place the record on the base.
The pin on the base element must protrude through the center hole of the record.
Place the applicator cup (dispenser) on the pin.
💡 Tip from Dr. DISCO:
Warm the DISCOFILM bottle in a water bath (approx. 25–30°C) beforehand. This will make the liquid more pliable and allow you to clean more sides of the record with one filling!
2. Application
Remove the cap from the DISCOFILM bottle.
Pierce the seal with a pointed object (e.g., a spike).
Press lightly on the bottle and fill the applicator with liquid up to the calibration mark.
➡️ Slowly turn the applicator clockwise over the record.
➡️ This should create an even, continuous film that covers all the grooves.
➡️ If there is not enough liquid, simply refill and continue applying.
➡️ Then remove the applicator.
3. Drying & removal
Allow the film to dry completely – approx. 2-4 hours, depending on the room temperature.
Now all dirt particles are bound in the film.
📌 How to peel off the film:
Stick a piece of adhesive tape approx. 5 cm long halfway onto the edge of the record.
Press it down firmly and slowly peel off the film.
❗ Note:
If the film tears when you peel it off, it was probably applied too thinly. No problem—just apply another coat and let it dry as usual.
How to use DISCOFILM bottle with sponge applicator—step by step
1. Application
Pull the cap off the DISCOFILM bottle.
Carefully pierce the sealing membrane with a pointed object (e.g., an awl).
Now apply DISCOFILM evenly and generously to the record using a sponge or brush.
Make sure that a homogeneous, closed film forms over all the grooves.
💡 Tip from Dr. DISCO:
Warm the DISCOFILM bottle in a water bath (approx. 25–30°C) beforehand. This will make the liquid more pliable and allow you to clean more sides of the record with one filling!
2. Drying & removal
Allow the film to dry completely – approx. 2-4 hours, depending on the room temperature.
All dust and dirt particles are now bound in the film.
➡️ Stick half of an approx. 5 cm long adhesive strip onto the edge of the record and press it firmly onto the dried film.
➡️ Pull the film off slowly and evenly – using the protruding adhesive strip.
❗ Note:
If the film tears when you pull it off, it was probably applied too thinly. No problem – just apply a new layer and repeat the process.
